Hornady Lock-N-Load Case Feeder Uživatelský manuál

CASEFEEDERLOCK-N-LOAD®OWNER'S MANUAL

Pivot AdapterPlace the Pivot Adapter (18) on top of the pivot for small rifle cases. Refer to page 13 for proper Pivot Adapter Bushing (51 or 52).1516

Feed Tube EndPush RodFeed TubeSelect the proper Feed Tube and insert it in the top of the Feed Tube End. If you select the Feed Tube End, you will hav

Placing the Feed Bowl Hopper on the AssemblySelect the Case Feed Plate for your application. Refer to page 13.To install the Case Feed Plate, place F

Base DiameterV-BlockFeed PlateFeed TubeFeed Tube EndPivot Adapter BushingDrop TubeSmall Pistol(9mm, 40 S&W, etc.)<0.43".27" – .30&qu

Cap ScrewAdjusting the Cam WireThe Cam Wire determines the timing of the Case Feed Slide and must be adjusted to allow the case to easily slide into t

TroubleshootingTips for Trouble-Free Operation of the Lock-N-Load® AP™ and Case FeederProblems SolutionsPowder dropping around case• Correct bushing

Rifle Dies & Reloading Essentials (Reference Chart)Rifle CartridgeBullet Diameter (inches)Die SetDie SeriesFull-Length Size DieSeating DieExpande

Rifle Dies & Reloading Essentials (Reference Chart)Rifle CartridgeBullet Diameter (inches)Die SetDie SeriesFull-Length Size DieSeating DieExpande

Rifle Dies & Reloading Essentials (Reference Chart)Rifle CartridgeBullet Diameter (inches)Die SetDie SeriesFull-Length Size DieSeating DieExpande

Pistol Dies & Reloading Essentials (Reference Chart)Pistol CartridgeBullet Diameter (inches)Die SetDie SeriesFull-Length Size DieSeating DieExp

See pages 4-5See pages 4-5See pages 4-5Table of ContentsASSEMBLY ... Page 3CHANGE-OVERS ..

780308-REV2 09/2014P.O. Box 1848, Grand Island, Nebraska 68802-1848 308-382-1390 • 800-338-3220 • Fax: 308-382-5761 www.hornady.com • Hornady.

Lock-N-Load® AP™ Case FeederOVERVIEWYour new AP™ Case Feeder has been packaged to insure minimal vibration and damage during transportation.Remove all

Item No.Production Part No. Qty. Description1 398441 1 Case Feed Bowl2 398313 4 10-32 x ¾ FHSCS4 398445 4 8-32 x 3/4 Screw5 398443 1 Case Feed Funnel

Lock-N-Load® AP™ Case FeederEXPLODED VIEWASSEMBLY- 5 -ASSEMBLY: CASE FEEDER

¼-20 1 ¼" Cap Screw (Full Size)5454Attaching the Square Tubing to the frame of the AP™ Press.Place the ¼" Flat Washers (48) on the ¼-20 x 1

¼-20 x 1 ½" Cap Screw (70) (Full Size)¼-20 x 1 ½" Cap Screw (Full Size)678Cam Wire SupportPivot BlockFeed Tube Mounting BracketCap ScrewCam

Installing the V-Block onto the case slide.With the Ram at the bottom of the stroke (idle position), set the V-Block onto the Case Slide (38).Refer t

Set the Pivot (19) on top of the Pivot Block (29). Make sure you line up the under cut in the bottom of the pivot with the Torsion Spring (23). The le